Natural hair dye Coleston 50 ml 4/6 Burgundy red

Coliston Naturals Hair Dye Red Burgundy contains strong colored dyeing materials and nourishing serum with natural extracts that vary depending on the nature of the color, such as cinnamon extract for brown hair, chamomile extract for blonde hair, pomegranate extract for red hair, and I can choose from many attractive colors for Coliston Naturals dye. Important instructions before dyeing hair using Coliston Naturals Purple Red: 1- Do not use the dye on wet hair and it is preferable not to wash the hair before the coloring process for three days. 2- You should wait 5-6 months if you have used henna on the hair because the dye cannot penetrate the layers formed by henna on the outer layer of the hair, resulting in uneven colors. 3- This dye is not used for eyebrows. 4- A sensitivity test must be performed 48 hours before the coloring or dyeing process. 5- For the best desired results, perform a strand test. Method of using Coliston Naturals Purple Red dye: 1- Preparing the coloring cream mixture: Empty the contents of the tube into a non-metallic dish (made of glass, plastic, or porcelain), then add the developer liquid and mix them together using a dye brush until you get a completely homogeneous dye mixture. Apply the dye mixture to your hair immediately after mixing well for the best color result. 2- Applying the coloring cream mixture: For the first time dyeing, apply the dye mixture to unwashed hair strand by strand using a dye brush. Make sure to apply the dye mixture to all hair and not leave any part out, then comb your hair with a wide-tooth comb to distribute the dye evenly over all hair. To dye the roots, divide your hair into sections and apply the dye mixture to each section separately, leaving it on your hair for 20 minutes. Then comb your hair evenly towards the tips. 3- Duration of leaving the product on the hair: The product should be left on the hair for 30 minutes, 20 minutes for the roots and 10 minutes for the rest of the hair. The color of the dye mixture may change during this period. 4- Finishing the dye: After the dyeing time, rinse the dye emulsion thoroughly with warm water. To fix the color, apply conditioner to your damp hair, leave it for 5 minutes, then rinse well with water. It gives you the smoothing serum with the healthy appearance you desire. Sensitivity test procedure on the skin: Must be done 48 hours before the coloring process. The tools needed for the sensitivity test are: cotton, cotton swab, plastic container, plastic spoon. 1- Open the cap of the developer solution tube number 2 and then open the cap of the coloring cream tube number 1. 2- Mix a small equal amount of coloring cream and developer solution in the plastic container. 3- Quickly close the caps of the coloring cream and developer solution. 4- Place a small amount of the prepared mixture behind your elbow on a 1 cm square area. Leave it to dry and do not rinse the mixture from behind your elbow for 48 hours. During bathing, protect the area with a tight bandage, then remove the bandage immediately afterward. 5- Check the test area after 48 hours. If there is no reaction, you are ready to proceed with the coloring process. 6- If a rash, burning sensation, or itching occurs, you may be allergic to one of the product's components, and you should stop using it immediately. Strand test for Coliston Naturals Purple Red dye: Test the color on a hair strand during each coloring to determine the best timing for highlighting and to achieve the best result, considering that chemical treatments such as curling, straightening, previous coloring, and sun exposure all affect the color outcome and timing needed. The tools needed for the strand test are: scissors, adhesive tape, and a clock. Strand test steps for Coliston Naturals Purple Red dye: 1- Cut a quarter inch of your dry hair that is dark or has a lot of white hair near the scalp, then stick the strand with tape at the cut site. 2- Apply the remaining mixture used for the sensitivity test over the strand, covering it completely, then start monitoring the time. 3- After 15 minutes, check the strand. If the color is not as desired, return the strand to the plastic container with the mixture and monitor the color periodically until 25 minutes pass. For very light blonde color, a more saturated color, or to cover resistant white hair, you may need to leave the coloring up to 45 minutes.