Uniview NSW2010-5GT-POE-IN-UK 4-Port Gigabit PoE Switch, 60W

The Uniview NSW2010-5GT-POE-IN-UK is an unmanaged 5-port gigabit switch with four PoE ports sharing a 60W budget and one uplink. It fits small villas, shops and clinics running up to four cameras or access points without separate power adapters.

====

The Uniview NSW2010-5GT-POE-IN-UK is a compact five-port gigabit switch for small installations. Four ports deliver power over the Ethernet cable, and the fifth links to your router or NVR. The PoE budget is 60W in total, with up to 30W on any single port, so four IP cameras, access points or desk phones can run without their own power adapters. Think of a small villa, a shop, a clinic or a reception desk where only a handful of devices need power and data.

Key specs at a glance

The switch belongs to Uniview's (UNV) unmanaged NSW2010 series, so there is nothing to configure. Plug in the cables and it works. Key figures:

• 4 × 1000 Mbps PoE ports plus 1 × 1000 Mbps non-PoE port.
• 60W total PoE budget, up to 30W per port on IEEE 802.3at, backward compatible with 802.3af devices.
• 10 Gbps switching capacity, 7.44 Mpps forwarding rate and a 2K MAC table.
• 65W maximum power draw from a 100 to 240V AC input.

Fanless and palm-sized

At 140 × 76.7 × 27.7 mm and under 1 kg, it has no cooling fan at all. That means zero noise, so it can sit inside a reception counter or a small cabinet beside the router. The rated operating range is 0 to 40°C, so keep it in an air-conditioned or ventilated spot rather than a rooftop water-tank room in a Riyadh summer.

Built-in protection for your devices

Before sending power, the switch checks what is plugged in. It will not damage non-PoE or non-standard devices, so a laptop or printer connected to a PoE port by mistake simply gets data. Port power priority is supported, which keeps critical devices running when total draw nears the limit.

Where it fits in Saudi Arabia

• A villa or istiraha with four outdoor cameras: one cable per camera, with the fifth port going to the NVR.
• A shop or pharmacy: two cameras, an IP phone and an access point on a single switch.
• A small office: adds ports to an STC, Mobily or Zain router and powers two phones and an AP.
• A clinic: one camera at the entrance, one at the cashier, plus the reception phone.

Compatibility

Any 802.3af or 802.3at powered device works, from any brand: Uniview and third-party cameras, access points, IP phones and intercom stations. Power is delivered in Mode A on pins 1, 2, 3 and 6. In the default mode, every port can talk to every other port.

NSW2010-5GT-POE-IN-UK or NSW2010-10GT-POE-IN?

The NSW2010-10GT-POE-IN doubles the PoE ports to 8, adds a second uplink, and raises the budget to 120W, but it has one fan. Pick the 5-port model for four devices or fewer and a silent install. Move up to the 10GT if you plan five to eight cameras.

Frequently Asked Questions

How many cameras can the NSW2010-5GT-POE-IN-UK power?

Up to four PoE cameras, as long as their combined draw stays within 60W. Each port supplies up to 30W.

Does it need any configuration?

No. It is an unmanaged switch: connect the cables and power, and it starts working.

Is it noisy?

No. It has zero fans, so it runs silently.

Specifications

• Model: NSW2010-5GT-POE-IN-UK
• Series: NSW2010 Gigabit Ethernet Switches (unmanaged)
• Ports: 4 × 1000 Mbps PoE RJ45 + 1 × 1000 Mbps RJ45
• Standards: IEEE 802.3, 802.3u, 802.3az, 802.3x, 802.3af, 802.3at
• Switching capacity: 10 Gbps
• Forwarding rate: 7.44 Mpps
• MAC address table: 2K
• Packet buffer: 1 Mbit
• PoE standard: IEEE 802.3af, IEEE 802.3at
• PoE mode: Mode A (1236)
• PoE budget: 60W total, up to 30W per port
• PoE features: Automatic PD detection, safe for non-PoE devices, port power priority
• Switching: Store-and-forward, line-speed forwarding, IEEE 802.3x flow control and half-duplex backpressure, Auto-MDI/MDIX
• Working modes: Default: all ports communicate
• Power input: AC 100-240V, 50/60Hz
• Max power consumption: 65W
• Cooling fans: 0 (fanless)
• Operating temperature: 0°C to 40°C (32°F to 104°F)
• Storage temperature: -40°C to 70°C
• Operating humidity: 10% to 90%, non-condensing
• Storage humidity: 5% to 90%, non-condensing
• Indicators: PWR: solid when AC input is normal; PoE: solid when PoE is normal, flashing when abnormal; LINK/ACT: flashing during data transfer
• Dimensions (W × D × H): 140 × 76.7 × 27.7 mm (5.5 × 3 × 1.1 in)
• Weight: Under 1 kg

Features

• 4 gigabit PoE ports at up to 30W each: one cable carries both data and power to each camera or AP.
• 60W total PoE budget: enough for four mid-power devices running at the same time.
• One 1000 Mbps uplink: connects to your router or NVR.
• Zero fans: silent operation inside a reception desk or small cabinet.
• 140 × 76.7 × 27.7 mm body: sits next to the router without taking up space.