DSPPA PAVA9002 Network Control Terminal for PAVA9500 Voice Alarm
1208.03ر.س
Product description
The DSPPA PAVA9002 carries audio and control data between a PAVA9500 voice alarm host, its expansion amplifiers and paging microphones over a LAN, supporting up to 30 amplifiers and 8 microphones. It suits malls, office buildings and exhibition halls spread over several floors or buildings.
====
The DSPPA PAVA9002 is neither an amplifier nor a microphone. It is the bridge between a PAVA9500 voice alarm system and the building's LAN. Normally the PAVA9500 devices talk to each other over a CAN bus with direct cable runs; this terminal carries that audio and control data across the network instead, so expansion amplifiers and paging mics in another building or on a distant floor can reach the host. DSPPA positions it for small emergency broadcast systems in small malls, office buildings and exhibition halls, which also handle daily announcements and background music.
What the DSPPA PAVA9002 does
The unit runs in one of four modes, chosen with DIP switches on the rear:
- Host sending: streams PAVA9500 audio over the network by multicast, within the same LAN.
- Expansion amplifier receiving: picks up the stream and hands it to a PAVA9500E expansion amplifier, up to 30 amplifiers.
- Remote mic sending: takes audio from a PAVA9008 paging mic or PAVA9009 fireman mic and sends it by unicast, across network segments.
- Host mic receiving: delivers microphone audio to the host, up to 8 mics per system.
CAN ports and cable distances
The rear carries RJ45-CAN ports labeled RM and EXT, each combining a CAN bus with a balanced audio output or input. One port can chain up to 3 devices over 300 m, or reach a single device at up to 600 m, using CAT5e cable or better. The RM ports supply DC48V to the paging mic, so the mic needs no local power adapter.
Backup power and fault indicators
There are two DC24V/2.5A inputs, main and backup, with automatic switchover. Yellow LEDs on the front flag a network fault, an AC mains failure or a DC backup failure, and four green LEDs show which mode is active. Operating temperature is -20 to +50°C.
Where it fits in Saudi Arabia
- Malls and commercial complexes spread over several buildings, with the host in one control room.
- Office buildings and towers: an expansion amplifier per group of floors and a paging mic at reception.
- Exhibition halls: linking distant halls to the same voice alarm and background music system.
- University campuses and large schools whose buildings already share one network.
Compatibility and installation
The terminal belongs to DSPPA's PAVA9500 system. It comes in a black iron housing for wall mounting and is powered through an AC110-240V adapter.
PAVA9002 or PAVA9002S?
The PAVA9002S is not a network unit; it is the rack-mount kit for this terminal: a fixing panel plus 3 upper and lower connectors. Choose it when devices are spread across buildings and you want to use the existing LAN.
Frequently Asked Questions
Is the DSPPA PAVA9002 an amplifier?
No. It is a network terminal that carries audio and control data between the PAVA9500 host, expansion amplifiers and mics over a LAN; amplification happens in the PAVA9500E expansion amplifiers.
How many amplifiers and mics does it support?
1 to 30 expansion amplifiers and up to 8 paging mics per system, according to the official datasheet.
Does it work with other PA systems?
DSPPA lists it only with the PAVA9500, PAVA9500E, PAVA9008 and PAVA9009, and does not mention MAG6000 or DSP9000 compatibility.
Specifications
- Model: PAVA9002
- Type: Fire alarm audio notification system network control terminal
- Compatible system: PAVA9500 host, PAVA9500E expansion amplifiers, PAVA9008 paging mic, PAVA9009 fireman mic
- Operating modes: Expansion amp receiving, remote mic sending, host sending, host mic receiving (DIP-switch selected)
- RJ45-CAN ports: RM1/RM2 TX, EXT1/EXT2 TX, RM1/RM2 RX, EXT1/EXT2 RX (CAN bus plus balanced output or input)
- CAN bus distance: Up to 3 cascaded devices per port at 300 m, single device up to 600 m, CAT5e or better
- LAN connection: RJ45
- Capacity: 1 to 30 expansion amplifiers, up to 8 paging mics per system
- Transmission: Host sending by multicast (LAN only); paging mics by unicast across segments
- Paging mic input sensitivity (RJ45): ±3000mV (±300mV)
- Expansion amp input sensitivity (RJ45): ±1500mV (±150mV)
- Host sending output level: ±1500mV (±150mV); mic output ±3000mV (±300mV)
- Frequency response: RX RM 100Hz-12kHz (±3dB); TX EXT 50Hz-16kHz (±3dB)
- Distortion / S/N: <1% / ≥76dB (A-weighted)
- RM bus power: DC48V (±5V)
- Power: DC24V/2.5A (±3V) main + DC24V/2.5A backup, operating range DC21-28V
- Adapter input: AC110V-240V, 50/60Hz
- Indicators: Power, network, AC fault, DC fault, plus 4 mode indicators
- Housing and mounting: Black iron, wall-mounted (PAVA9002S rack kit sold separately)
- Operating temperature / humidity: -20 to +50°C / 20% to 80% RH, non-condensing
- Unit dimensions: 165×115×55 mm
- Net weight: 0.65 kg
Features
- Four DIP-switch modes: the same unit works at the host, at an expansion amplifier or at a paging microphone.
- Up to 30 expansion amplifiers and 8 paging mics per system: extend the voice alarm system without long CAN runs between buildings.
- Main and backup DC24V/2.5A inputs with automatic switching: the terminal keeps running if one supply fails.
- Fault LEDs for network, AC mains and DC backup: technicians see where the problem is from the front panel.
- Compact 165×115×55 mm iron housing for wall mounting: fits in a network room, or in a rack with the PAVA9002S kit.
