DSPPA MAG6701 IP Network Terminal with 60W 100V Amplifier

2037.08

Product description


The DSPPA MAG6701 is an IP PA endpoint with a built-in 60W 100V amplifier, so loudspeakers connect directly without a separate amp. It suits each zone of a school, hotel or compound, adding USB and SD playback and a schedule that keeps running if the link to the server is lost.

====

The DSPPA MAG6701 is a network PA endpoint with its own 60W digital amplifier on a 100V line. It receives audio from the system server over the network and drives the speakers wired to it directly, so a zone does not need a separate amplifier. The unit mounts on a wall and suits a classroom wing, a hotel floor or a shop unit inside a mall.

DSPPA MAG6701 specs at a glance

  • 60W single-channel amplifier on a 100V line, distortion no more than 1%.
  • Two network ports, LAN1 and LAN2, with dual-network redundancy.
  • MP3 player for USB drives up to 32GB and Micro SD cards.
  • Audio decoding up to 48kHz and 16-bit.
  • AUX in, AUX out and two microphone inputs.
  • Wall mounting through four screw holes; 222 × 195 × 56 mm.

The schedule keeps running without the server

Timing runs inside the unit and does not depend on the host, while the Micro SD slot holds scheduled programs for offline playback. If the school network goes down, class bells and timed programs in that zone carry on. A USB stick covers local background music or recitation whenever no network stream is playing.

Built-in amplifier with a standby input

The 100V output powers several ceiling or wall speakers up to a 60W total load. A 100V input on the back accepts a standby amplifier, and the unit switches to it in about 220ms when required. Protection covers overcurrent, overheating and over- and under-voltage, and an amplifier protection LED lights on a short circuit in the speaker line.

Local control and emergency outputs

The MAG6701 plays background music, emergency pages and alarm signals sent by the host, with source priority set over the network. On site, you adjust volume and switch between AUX, microphone and MP3 from the front keys or the IR remote. An EMC emergency output and a COM/SC short-circuit output are controlled by the server, and an extension port supplies DC power to add-on devices.

Where it goes in Saudi buildings

  • Schools: one unit per classroom wing, with timed bells that survive a network outage.
  • Hotels: separate background music and announcements for each floor or restaurant.
  • Malls: individual audio per shop while still receiving general pages from security.
  • Prayer rooms in compounds and hospitals: local USB playback plus building-wide announcements.

MAG6000 compatibility

The MAG6701 works with a system server such as the MAG6182II and takes live pages from stations like the MAG6588, MAG6510 and MAG6585. Mains input is AC220V/50Hz.

MAG6701 or MAG6801?

The amplifier is the difference. The MAG6701 carries a 60W 100V amplifier, mounts on a wall and adds USB/SD playback and two mic inputs. The MAG6801 has no amplifier: it sends a 1V line-level signal to an existing amp, sits in the equipment room at 483 mm wide, and adds a fire-panel emergency input and a 24V alarm output. Use the MAG6701 for a new zone and the MAG6801 to put an existing amplifier on the network.

Frequently Asked Questions

How many speakers can the DSPPA MAG6701 drive?

It delivers 60W on a 100V line, so connect 100V speakers whose total tapped wattage stays within 60W.

Does the MAG6701 keep working if the network fails?

Yes. Its timer runs without the host, playing scheduled programs from Micro SD and files from USB up to 32GB.

Can the MAG6701 be wall mounted?

Yes. It has four screw holes for wall installation and measures 222 × 195 × 56 mm.

Specifications

  • Model: MAG6701
  • Type: IP network terminal with built-in 100V amplifier
  • System: DSPPA MAG6000 IP network PA system
  • Built-in amplifier power: 60W single channel, 160Ω, 100V output
  • Amplifier max harmonic distortion: ≤1%
  • Audio decoding: Up to 48kHz, 16-bit
  • Network: LAN1 and LAN2 with daisy-chain and dual-network redundancy
  • Local playback: MP3 from USB disk (up to 32GB) and Micro SD
  • Interfaces: 1× AUX in, 1× AUX out, 2× MIC in, EMC emergency output, COM/SC short-circuit output, 100V in, 100V out, DC-powered extension port
  • Control: Front keys, display, LED indicators, IR remote, network-set source priority
  • AUX IN sensitivity: 300mV±30mV
  • AUX IN frequency response: 80Hz-16kHz (±3dB)
  • AUX IN distortion / noise / SNR: ≤1% / 14mV / ≥77dB
  • AUX OUT level: 1000mV±100mV
  • AUX OUT frequency response: 35Hz-20kHz (±3dB)
  • AUX OUT distortion / noise / SNR: 0.1% / 0.12mV / ≥77dB
  • MIC input sensitivity: 3.5mV±1mV
  • MIC frequency response: 80Hz-16kHz (±3dB)
  • MIC distortion / noise / SNR: ≤0.5% / 14mV / ≥77dB
  • USB/SD/NET frequency response: 85Hz-16kHz (±3dB)
  • USB/SD/NET distortion / noise / SNR: ≤0.4% / 14mV / ≥77dB
  • 100V backup changeover time: 220ms (±50ms)
  • Protection: Overcurrent, overheat, over-voltage, under-voltage
  • Power supply: AC220V/50Hz
  • Mounting: Wall mount (4 screw holes)
  • Unit dimensions (L×W×H): 222×195×56 mm
  • Net weight: 2.35 kg

Features

  • Built-in 60W amplifier on a 100V line: drives several ceiling or wall speakers in the zone directly.
  • Two network ports (LAN1, LAN2): daisy-chain units and keep the link across two networks.
  • MP3 player for USB up to 32GB and Micro SD: local programs when there is no network audio.
  • Host-free timer: scheduled bells and programs continue even if the server connection drops.
  • 100V input for a standby amplifier with 220ms changeover: speakers keep receiving audio when needed.

Questions you might have

‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌