Uniview NSW2010-26GT2GC-POE-IN 24-Port Gigabit PoE Switch, 370W

The Uniview NSW2010-26GT2GC-POE-IN is the largest NSW2010 model: 24 gigabit PoE ports sharing 370W, two RJ45 uplinks and two combo ports that work as copper or fiber. It is built for warehouses, malls and hospitals feeding dozens of cameras and access points from one rack room.

====

The Uniview NSW2010-26GT2GC-POE-IN puts 24 gigabit PoE ports in a single 440 mm chassis with a 370W budget, so one rack room can power a large fleet of cameras or access points. It adds two RJ45 uplinks and two combo ports, each of which takes either copper or a fiber module. This is the model for contractor projects, warehouses and commercial complexes where 16 ports are not enough.

The numbers

It is the largest model in Uniview's (UNV) unmanaged NSW2010 series. Its key specifications:

• 24 × 1000 Mbps PoE RJ45, 2 × 1000 Mbps RJ45 and 2 × 1000 Mbps combo ports.
• 370W total PoE budget, up to 30W per port, on 802.3af and 802.3at.
• 56 Gbps switching capacity, 41.7 Mpps forwarding, 8K MAC table and 4 Mbit buffer.
• 100 to 240V AC input, 400W maximum draw and two cooling fans.

What a combo port gives you

A combo port has two physical sockets, an RJ45 jack and an SFP slot, and you use one at a time. If the core switch is in the same room, run a normal copper cable. If it sits in another building, fit a gigabit fiber module instead. The switch supports 802.3z, the gigabit-over-fiber standard.

Planning around 370W

With all 24 ports loaded, the average works out to about 15W per port, comfortable for most fixed cameras. For PTZ cameras or high-draw access points, total their maximum figures from each datasheet before you buy. When demand nears the limit, port power priority keeps key devices running, and power only goes to devices that request PoE.

Saudi use cases

• Logistics warehouses in Riyadh or Dammam: 24 indoor and outdoor cameras, with EXTEND mode reaching 250 m to fences and loading bays.
• Malls and commercial centers: corridor and parking cameras from a rack room on each floor.
• Hospitals and clinic complexes: cameras, access points and IP phones together in default mode.
• Contractor projects: one switch instead of three small ones means fewer failure points and cleaner cabling.

It works with any 802.3af or 802.3at device from Uniview or other brands, using Mode A on pins 1, 2, 3 and 6, and the uplinks connect to larger recorders such as a 32-channel NVR.

Rack installation

At 440 × 207 × 44 mm it matches a 1U, 19-inch rack slot, and it weighs under 5 kg. The operating range is 0 to 40°C, and the two fans need clear airflow on both sides. With a 400W maximum draw, size the rack UPS before installation.

NSW2010-26GT2GC-POE-IN or NSW2010-18GT2GP-POE-IN?

The NSW2010-18GT2GP-POE-IN has 16 PoE ports, a 185W budget and two dedicated SFP slots in a 280 mm body with one fan. Pick the Uniview NSW2010-26GT2GC-POE-IN for more than 16 devices, more than 185W, or uplinks that can switch between copper and fiber. For systems of up to 16 cameras, the 18GT2GP is enough.

Frequently Asked Questions

What is the difference between the combo and SFP ports on the NSW2010-26GT2GC-POE-IN?

A combo port accepts either a copper RJ45 cable or an SFP fiber module, one at a time. A pure SFP port takes fiber only.

Is it rack-mountable?

It measures 440 mm wide and 44 mm high, which matches a 1U, 19-inch rack slot.

How many cameras can it run?

Up to 24 PoE cameras with a 370W total budget and up to 30W per port, plus uplinks for the NVR and network.

Specifications

• Model: NSW2010-26GT2GC-POE-IN
• Series: NSW2010 Gigabit Ethernet Switches (unmanaged)
• Ports: 24 × 1000 Mbps PoE RJ45 + 2 × 1000 Mbps RJ45 + 2 × 1000 Mbps combo
• Standards: IEEE 802.3, 802.3u, 802.3z, 802.3ab, 802.3x, 802.3af, 802.3at, 802.3az
• Switching capacity: 56 Gbps
• Forwarding rate: 41.7 Mpps
• MAC address table: 8K
• Packet buffer: 4 Mbit
• PoE standard: IEEE 802.3af, IEEE 802.3at
• PoE mode: Mode A (1236)
• PoE budget: 370W total, up to 30W per port
• PoE features: Automatic PD detection, safe for non-PoE devices, port power priority
• Switching: Store-and-forward, line-speed forwarding, IEEE 802.3x flow control and half-duplex backpressure, Auto-MDI/MDIX
• Working modes: Default: all ports talk to each other; VLAN (secure): downlink ports talk to uplink ports only; EXTEND (surveillance): up to 250 m, downlink ports talk to uplink ports only
• Power input: AC 100-240V, 50/60Hz
• Max power consumption: 400W
• Cooling fans: 2
• Operating temperature: 0°C to 40°C (32°F to 104°F)
• Storage temperature: -40°C to 70°C
• Operating humidity: 10% to 90%, non-condensing
• Storage humidity: 5% to 90%, non-condensing
• Indicators: PWR: solid when AC input is normal; PoE: solid when PoE is normal, flashing when abnormal; LINK/ACT: flashing during data transfer
• Dimensions (W × D × H): 440 × 207 × 44 mm (17.3 × 8.1 × 1.7 in)
• Weight: Under 5 kg

Features

• 24 gigabit PoE ports at up to 30W each: a large camera system or a full AP network on one switch.
• 370W total PoE budget: an average of about 15W per port with all 24 ports loaded.
• Two gigabit combo ports: use copper RJ45 or an SFP fiber module on each, depending on distance.
• 56 Gbps switching and 41.7 Mpps forwarding: full gigabit speed on every port.
• 440 mm wide, 44 mm high: sized for a 19-inch rack at 1U.