DSPPA DSP9102 IP Network Fire Alarm Terminal with 32 Inputs
2025.04ر.س
Product description
The DSPPA DSP9102 is a 1U network terminal that takes up to 32 alarm outputs from a fire panel and switches a DSPPA DSP9100 IP PA system into emergency broadcast for the affected zone and, if programmed, its neighbours. It fits malls, schools, hotels and hospitals that want the fire system to control the speakers during an incident.
====
The DSPPA DSP9102 is a 1U network fire alarm terminal that links a building's fire panel to a DSPPA IP paging system. It accepts 32 independent alarm inputs, and the moment one of them trips, it reports to the PA server, which forces the system into emergency broadcast mode. If you run a DSP9100 IP PA system in a mall, school or hotel, this is the unit that lets the fire system take control of the speakers.
DSPPA DSP9102 specifications at a glance
- 32 alarm input channels, each with its own LED on the front panel.
- Input type: dry contact (short circuit) or a 5 to 24 V signal.
- One RJ45 port at 10/100 Mbps, DHCP or static IP.
- Protocols: TCP/IP, UDP, ICMP and IGMP multicast.
- Universal power: 100 to 240 V AC, 50/60 Hz, fused.
Zone-based evacuation instead of whole-building alarms
Not every alarm needs every speaker. The networked host is pre-programmed to decide what happens for each input: broadcast only in the zone where the alarm started, or extend the message to several neighbouring zones. In a tower or a large mall, the floors closest to the incident hear the instruction first while the rest of the building is not thrown into panic. The alarm tone or recorded message for each case is chosen in the management software.
Hardware and front panel
The unit measures 44 × 430 × 213 mm, weighs 2.3 kg and has an anodized aluminium front panel. DSPPA lists an installation kit among its parts. The front carries a power switch, power and warning indicators and the 32 channel LEDs, so a technician can see which zone fired without logging in. Around the back you get the network port, the 32-way alarm connector and the power inlet.
Typical projects in Saudi Arabia
- Shopping malls and office towers in Riyadh and Jeddah, mapping fire zones to PA zones floor by floor.
- Schools and universities, where the daily paging system doubles as the emergency announcement system.
- Hotels in Makkah and Madinah that need evacuation messages aimed at the affected floors.
- Hospitals and warehouses collecting alarms from many areas into one control room.
Compatibility and expansion
DSPPA places the DSP9102 in the System Host group of its DSP9100 IP network PA system, managed through the DSP9000 software. Need more than 32 fire zones? Add another DSP9102 on the same network and the controlled area grows with it. On the fire side, the panel only needs a dry-contact or 5 to 24 V output per zone.
DSP9102 or MAG6416II?
Both are 32-channel emergency interfaces. The DSP9102 is officially documented for DSP9000 / DSP9100 systems, with a 1U chassis and 100 to 240 V power. If your server is a DSP9100, pick the DSP9102. If your system is an analog MP98 rack, the closer match is the MP9815E emergency unit.
Frequently Asked Questions
How many fire zones can the DSPPA DSP9102 handle?
32 per unit, each on its own channel with an LED. Add more units on the same PA network if you need more zones.
What kind of signal does it need from the fire panel?
A dry contact (short circuit) or a 5 to 24 V signal, according to DSPPA's datasheet.
Does the DSP9102 work with any PA system?
It is built for DSPPA's DSP9100 IP network PA system and managed with the DSP9000 software. DSPPA does not list third-party PA compatibility.
Specifications
- Model: DSP9102
- Type: IP Network Fire Alarm Terminal (network fire collector)
- System: DSP9000 / DSP9100 IP network PA system (System Host group)
- Channels: 32
- Display: LED (one indicator per channel)
- Protocols: TCP/IP, UDP, ICMP, IGMP (multicast)
- Neighbour-zone activation: Multiple, programmable
- Trigger signal level: 5-24 V
- Input mode: Short circuit or 5-24 V
- Network: RJ45 10/100 Mbps, DHCP or static IP
- Protection: AC fuse × 1
- Power input: 100-240 V AC, 50/60 Hz
- Panel items: Power switch, power indicator, warning indicator, installation kit, network port, 32-way alarm signal interface, power inlet
- Form factor: 1U, anodized aluminium panel
- Dimensions (H × W × D): 44 × 430 × 213 mm
- Weight: 2.3 kg
Features
- 32 independent alarm inputs: one channel per fire zone, each with its own front-panel LED.
- Dry contact or 5 to 24 V trigger: accepts a contact or voltage output from the fire panel for each zone.
- Zone or neighbour-zone emergency paging: programmed on the PA host so the nearest floors hear the evacuation message first.
- 10/100 Mbps LAN with DHCP or static IP: place it anywhere on the PA network instead of running long audio cables.
- 1U, 2.3 kg chassis on 100 to 240 V power: a compact unit that runs on a wide mains voltage range.
