Uniview NSW3000-24T1GT1GC-POE-IN 24-Port PoE Switch, 370W Budget

The Uniview NSW3000-24T1GT1GC-POE-IN powers up to 24 IP cameras from a single box with a 370W PoE budget, backed by a Gigabit RJ45 uplink and a Gigabit combo port. It is a good match for surveillance projects in schools, compounds and factories.

====

Got 17 to 24 cameras on one site? The Uniview NSW3000-24T1GT1GC-POE-IN feeds all of them from a single switch with a PoE budget of up to 370W. You get 24 PoE ports at 10/100 Mbps, a Gigabit RJ45 uplink and a Gigabit combo port that accepts copper or fiber. It is part of the cloud-managed NSW3000 line from Uniview (UNV).

NSW3000-24T1GT1GC-POE-IN specs at a glance

• 24 × 10/100 Mbps RJ45 ports with PoE.
• Uplinks: 1 × Gigabit RJ45 and 1 × Gigabit combo.
• 8.8 Gbps switching capacity, 6.55 Mpps forwarding rate.
• 16K MAC table, 4 Mbit packet buffer.
• 370W PoE budget, up to 30W per port under 802.3at.

Splitting 370W across 24 ports

With all 24 ports drawing power at the same time, each one gets around 15.4W. That suits most fixed indoor and outdoor cameras and still leaves headroom for a few PTZ units that need up to 30W. Power delivery covers 802.3af and 802.3at in Mode A and Mode B.

Heavy PoE loads mean more heat. The unit is rated for 0 to 45°C with a single cooling fan, so mount it in a ventilated network room or cabinet, especially through a Riyadh or Eastern Province summer. A PoE load LED on the front lights once draw goes past 85% of capacity, your cue to move some cameras to another switch.

Watching devices from the management software

The management software shows a topology map with every connected video device (up to 64) and details of up to 32 other switches on the network. From the same interface you can upgrade firmware, export configuration and logs, and restart the switch.

• Up to 32 VLANs in access or trunk mode.
• Per-port rate limiting and broadcast storm control.
• Downlink port isolation, so cameras cannot see each other.
• Per-port PoE on/off with live power readings.

Where a 24-port PoE switch fits in KSA

• Schools: classrooms, corridors, yards and the main gate.
• Residential compounds and tower car parks.
• Small hotels and serviced apartments in Makkah and Madinah: floors, lifts and reception.
• Factories and workshops: production lines and storerooms.

Compatibility and cabling

Any IP camera or access point that supports 802.3af or 802.3at can be powered. Connect a recorder such as the Uniview NVR502-32B to the Gigabit port, and keep the combo port for fiber when the recording room sits in another building. Both uplinks can be aggregated when linking to a core switch that supports it.

Frequently Asked Questions

What is the difference between 370W and 385W on the NSW3000-24T1GT1GC-POE-IN?

370W is the power available to PoE devices; 385W is the maximum the switch itself draws from the mains.

Will it run PTZ cameras?

Yes. Each port supplies up to 30W under 802.3at, provided the total stays within 370W.

Does it need special cooling?

It has one fan and is rated up to 45°C, so a ventilated network room or cabinet is recommended.

Specifications

• Model: NSW3000-24T1GT1GC-POE-IN
• Category: Cloud Managed Ethernet PoE Switch
• Ports: 24 × 10/100 Mbps PoE RJ45, 1 × Gigabit RJ45, 1 × Gigabit combo
• Standards: IEEE 802.3, 802.3u, 802.3z, 802.3ab, 802.3x, 802.3af, 802.3at, 802.3az
• Switching capacity: 8.8 Gbps
• Forwarding rate: 6.55 Mpps
• Packet buffer: 4 Mbit
• MAC address table: 16K, dynamic MAC clearing
• PoE standards: IEEE 802.3af, 802.3at
• PoE budget: 370W total, up to 30W per port
• PoE modes: Mode A (1/2/3/6), Mode B (4/5/7/8)
• Priority ports: 1 to 8
• Ethernet: Full/half duplex and auto-negotiation, flow control, one link aggregation group of the two uplinks, port statistics, port enable/disable
• VLAN: Access and trunk, up to 32 VLANs
• PoE management: View PoE status and power, enable/disable PoE per port
• QoS: Port rate limiting, broadcast storm control
• Security: Downlink port isolation, login lock for up to 64 IP addresses
• Maintenance: Loop detection, N:1 port mirroring, video device discovery and topology, upgrade, factory reset, config import/export, log export and reboot from the software
• System: View up to 32 switches and up to 64 video devices on the same network
• Indicators: Power, PoE, Link/Act, PoE load alert (on above 85%)
• Cooling: 1 fan
• Power supply: 100 to 240V AC, 50/60Hz
• Max power consumption: 385W
• Dimensions (W × D × H): 440 × 244.8 × 44 mm
• Weight: 2.9 kg
• Operating temperature: 0 to 45°C
• Operating humidity: 5% to 90% RH, non-condensing
• Compliance: NDAA

Features

• 24 PoE ports at 10/100 Mbps: one cable per camera carries both power and video.
• 370W PoE budget, up to 30W per port: about 15.4W per port with all 24 ports loaded at once.
• Gigabit combo port: link a recording room in another building over fiber with an SFP module.
• PoE load LED: lights once draw exceeds 85% of capacity, helping you avoid cameras dropping from overload.
• Up to 32 VLANs and downlink port isolation: keep CCTV traffic apart from the office network and from other cameras.