Grandstream GWN7803PL Pro 24-Port PoE+ Switch with 10G SFP+
897ر.س
Product description
The Grandstream GWN7803PL Pro is a managed switch with 24 Gigabit PoE+ ports at up to 30W each, a 250W budget and two 10G SFP+ uplinks. It targets networks with many low-power devices such as IP phones, fixed cameras and standard access points.
====
The Grandstream GWN7803PL Pro is built for networks with lots of low-power devices: desk phones, fixed cameras and standard access points. It provides 24 Gigabit PoE+ ports at up to 30W each, a 250W budget and two 10G SFP+ uplinks. The "L" marks the lower-power version of the 24-port model, so you get the same ports and uplink speeds without paying for 60W capacity you may never use.
Grandstream GWN7803PL Pro specifications
- 24 × Gigabit RJ45, all PoE/PoE+ under IEEE 802.3af/at.
- Up to 30W per port, 250W total.
- 2 × 10G SFP+.
- 88 Gbps switching capacity, 44 Gbps non-blocking throughput.
- 4K VLANs.
Who a 250W budget is right for
With all 24 ports drawing power, the average is about 10.4W per port. Most desk IP phones and fixed cameras sit inside that figure, so one switch can cover a full office floor. Allocation is dynamic: a phone that draws little leaves headroom for an access point that needs more. If any single device needs more than 30W, this model's ports cannot supply it and the GWN7803PH Pro is the right choice.
Clear calls on a call center floor
Voice VLAN places IP phones on their own network automatically, and QoS gives voice traffic priority using five scheduling modes (SP, WRR, WFQ, SP-WRR and SP-WFQ). An agent's call stays clear while a colleague uploads a large file. Port power schedules can switch phones off after hours, and LLDP-MED power negotiation gives each phone only the power it asks for.
10G uplink and central management
The SFP+ ports carry traffic from all 24 devices to the core at 10G. Manage the switch from GDMS Networking, GWN Manager or the web UI, with 802.1X, ARP inspection and DHCP snooping for security. In a multi-floor building, put one of these on each floor and run fiber from its SFP+ ports to the core switch, so floor-to-floor distance stops being an issue.
Common Saudi use cases
- A Riyadh call center: 20 or more IP phones on one switch.
- A corporate or government office floor: a phone per desk plus corridor cameras.
- A hotel: PoE guest-room phones and corridor access points.
Compatibility
Works with 802.3af/at IP phones, cameras and access points from any vendor, connects to any IP PBX over the LAN like any switch, and shares a dashboard with other GWN devices.
GWN7803PL Pro, GWN7803PH Pro or GWN7802P Pro?
The GWN7803PH Pro has the same ports and uplinks but raises each port to 60W and the budget to 400W. The GWN7802P Pro has only 16 ports on the same 250W budget, with 60W per port. Choose the GWN7803PL Pro when you have many devices that each need 30W or less. Against the standard GWN7803P (24 PoE+ ports, 370W, four 1G SFP), the PL has a smaller budget but adds 10G uplinks.
Frequently Asked Questions
Can the GWN7803PL Pro power 24 IP phones?
The budget is 250W, about 10.4W per port with all ports in use. Check your phone's datasheet; most desk phones fall within that.
Does it support 60W PoE++?
No. Each port tops out at 30W under 802.3af/at. For 60W, choose the GWN7803PH Pro with the same port count.
How fast are the uplinks?
Two 10G SFP+ ports, with 88 Gbps total switching capacity.
Specifications
- Model: GWN7803PL Pro
- Series: GWN7800 Pro, Layer 2++ managed switch
- Ethernet ports: 24 × Gigabit RJ45
- Uplink ports: 2 × 10G SFP+
- Other ports: 1 × console (MGMT) port, reset pinhole
- PoE ports: 24 × PoE/PoE+
- PoE standard: IEEE 802.3af/at
- Max PoE per port: 30W
- Total PoE budget: 250W
- Switching capacity: 88 Gbps
- Forwarding rate: 65.472 Mpps
- Non-blocking throughput: 44 Gbps
- Forwarding mode: Store-and-forward
- Packet buffer: 8.4 Mb
- Latency: Under 4 µs
- MAC address table: Static, dynamic, filtering
- Jumbo frame: Up to 12288 bytes
- VLAN: 4K VLANs: port-based, 802.1Q, QinQ, MAC-based, protocol-based, VLAN translation, voice VLAN
- ARP/NDP: Static and dynamic entries
- Routing: IPv4 / IPv6 static routes
- Link aggregation: Static and LACP
- Spanning tree: STP/RSTP/MSTP/PVST(+)/RPVST(+), 16 MSTP/PVST instances
- Multicast: IGMP Snooping v2/v3, MLD Snooping v1/v2
- QoS: Port priority, priority mapping (802.1p, DSCP, IP precedence), SP/WRR/WFQ/SP-WRR/SP-WFQ scheduling, traffic shaping, rate limiting
- ACL: ACLs for Ethernet, IPv4 and IPv6
- DHCP: DHCP client, server, relay and snooping; DHCPv6 client and snooping; ND snooping
- IPv6: IPv4, IPv6 or dual-stack deployment
- Smart PoE: Dynamic per-port allocation, port power priority, per-port power limit, time-based port power schedules, LLDP-MED power negotiation
- Pro AV: Built-in Pro AV QoS, IGMP/MLD snooping for video, IEEE 1588v2 transparent clock (PTPv2)
- Security: User hierarchy, HTTPS/SSH/Telnet, 802.1X and MAC authentication, RADIUS/TACACS+, storm control, port isolation, port security and sticky MAC, IP/IPv6 source guard, DoS prevention, ARP inspection, CPU protection, loopback/BPDU/root protection, firmware signing, Kensington slot
- Management: Embedded web UI controller, GDMS Networking (cloud), GWN Manager, GWN routers, GWN App, CLI via console/Telnet/SSH, SNMP v1/v2c/v3, RMON
- Maintenance and diagnostics: SPAN/RSPAN mirroring, copper cable and fiber module diagnostics, ping, traceroute; upgrade via FTPS, TFTP, HTTP/HTTPS or local upload
- Stacking: Not supported (stacking is for GWN7806 Pro models only)
- Dual boot: Not listed for this model (GWN7806 Pro models only)
- LEDs: 1 tri-color system LED, 2 PWR/RPS LEDs, 26 data LEDs, 24 PoE LEDs
- Power input: 100-240V AC, 50/60 Hz
- Power consumption: 27.5W idle, 299.2W max (250W PoE)
- Surge / ESD: ±6 kV CM power, ±4 kV CM network ports, ±12 kV contact ESD
- MTBF: 70,000 hours
- Operating environment: 0 to 45°C, 10-90% RH non-condensing
- Storage environment: -10 to 60°C, 5-95% RH non-condensing
- Dimensions (L × W × H): 440 × 300 × 44 mm
- Weight: 3.06 kg
- Mounting: Desktop or 19-inch rack
- In the box: Switch, 25 cm ground cable, 4 rubber footpads, anti-trip power cord, 8 M3×6 mm flat-head screws, 1.2 m 10A AC cable, quick installation guide, regulatory paper, 2 × rack-mounting kits
- Certifications: FCC, CE, RCM, IC
Features
- 24 Gigabit PoE+ ports up to 30W: an IP phone or fixed camera on every port, no power adapters.
- 250W budget: about 10.4W per port with all ports loaded, enough for most IP phones and fixed cameras.
- Two 10G SFP+ uplinks: one fast link carries traffic from 24 devices to the core switch.
- Voice VLAN and QoS with five scheduling modes: call center voice gets priority over file transfers.
- 27.5W idle draw: lower than the PH version, at just 3.06 kg.
