DSPPA DMA120U 120W Mixer Amplifier with Bluetooth, USB and FM

1182.64

Product description


The DSPPA DMA120U is a 120W digital mixer amplifier from the DMA60U series, with mic inputs, 2 AUX inputs, USB, Bluetooth and FM radio in one box. It fits shops, cafes and clinics that need background music plus announcements over a modest number of speakers.

====

The DSPPA DMA120U is a 120W digital mixer amplifier and the step up from the DMA60U in DSPPA's DMA60U series. It mixes a microphone, music from a phone and FM radio, then drives ceiling or wall speakers in a shop, cafe or clinic. You get a 4-16 ohm output plus 70V and 100V constant-voltage taps, so the same unit handles two nearby speakers or a long cable run to a whole floor.

DSPPA DMA120U specifications

Rated output is 120W on 110-240V AC. The chassis is 88 mm tall and 430 mm deep, small enough for a shelf or a cabinet. Key figures from the official DSPPA datasheet:

  • Microphone inputs: MIC1 on the front, MIC2 and MIC3 balanced on the rear.
  • 2 AUX inputs and 1 AUX OUT to feed another device.
  • 1 EMC emergency input at 350mV sensitivity.
  • AUX frequency response of 80Hz-15kHz and THD below 1%.
  • Signal-to-noise ratio of 75dB or better on AUX and 71dB on mic.

Background music straight from your phone

Most small retail and food outlets want quiet music all day and the occasional announcement. The DMA120U has Bluetooth, a USB port and an FM tuner built in. Stream a playlist from your phone, plug in a flash drive, or switch sources with the MODE button or the infrared remote. A segment display shows the current source, and power-off memory restores your settings after an outage.

Microphone and chime take priority

DSPPA lists a fixed priority order: MUTE first, then EMC, alarm and chime at equal level, then MIC1, then everything else. So when staff speak into MIC1, the music steps aside. Two front-panel chime buttons, adjustable from level 0 to 15, play an attention tone before a message. Close the SIREN contact from an alarm panel and the amplifier sounds its siren even while music is playing.

Phantom power and a 24V input

MIC2 and MIC3 accept 48V phantom power via a rear switch, so a condenser desk mic at reception works without a separate supply. The rear panel also carries a DC 24V input labelled 10A for running from a backup DC source.

Where the DMA120U fits in Saudi Arabia

  • Fashion and fragrance stores in malls: background music and staff paging.
  • Clinics and dental centers: calling patients in the waiting area.
  • Cafes and restaurants: phone playback plus a mic for announcements.
  • Small offices and showrooms: several ceiling speakers on a 100V line, as long as their total wattage stays under 120W.

DMA120U or DMA250U?

Both share the same inputs and the same 4-16 ohm, 70V and 100V outputs. The difference is power (120W vs 250W) and size: the DMA120U is 280 mm wide and weighs 4.6 kg net, while the DMA250U is 330 mm wide and adds an AC voltage selector. Pick the DMA120U when your speakers add up to less than 120W; move to the DMA250U or DMA350U for larger spaces.

Frequently Asked Questions

How many speakers can the DMA120U drive?

On a 70V or 100V line, add up the tap wattage of each speaker and keep the total under 120W. On the low-impedance output it accepts a 4-16 ohm load.

Can I play music from my phone?

Yes. Bluetooth is built in, alongside a USB port for flash drives and an FM tuner.

Does it support condenser microphones?

Yes. The rear MIC2 and MIC3 inputs provide switchable 48V phantom power.

Specifications

  • Model: DMA120U
  • Series: DMA60U Series (DMA60U to DMA650U)
  • Rated output (AC): 120W
  • Speaker output: 4-16Ω, 70V, 100V (constant voltage)
  • Microphone inputs: MIC1 front, MIC2 and MIC3 balanced on rear
  • AUX inputs: 2 (AUX2 shared with MIC3 via selector switch)
  • Emergency input: 1× EMC input
  • Line output: 1× AUX OUT
  • Phantom power: +48V for MIC2/MIC3, rear switch
  • MIC1 / MIC2 sensitivity: 10mV ±1mV
  • AUX1 / AUX2 / EMC sensitivity: 350mV ±50mV
  • MIC frequency response: 120Hz-12kHz (±3dB)
  • AUX frequency response: 80Hz-15kHz (±3dB)
  • THD: <1%
  • SNR (A-weighted): AUX ≥75dB, MIC ≥71dB
  • Tone controls: Bass and treble ±10dB (±2)
  • Built-in sources: USB, Bluetooth, FM radio (with FM antenna socket)
  • Chimes and alarms: Chime 1 and Chime 2 (level 0-15), SIREN short-circuit trigger with alarm output, MUTE short-circuit trigger
  • Priority: MUTE > EMC = Alarm = Chime > MIC1 > others (no chime during alarm)
  • Control and display: Segment display, IR remote control, power-off memory
  • AC power supply: AC 110-240V, 50/60Hz
  • DC input (rear-panel label): +24V / 10A
  • Rear-panel switches: Phantom switch, AUX2/MIC3 selector, MIC gain, alarm gain
  • Operating temperature: -10 to 50°C
  • Relative humidity: 20% to 80%
  • Dimensions (D × W × H): 430 × 280 × 88 mm
  • Net weight: 4.6 kg

Features

  • 120W with 4-16 ohm, 70V and 100V outputs: drive speakers directly or run a long 100V line to several ceiling speakers.
  • Mic inputs with 48V phantom on MIC2 and MIC3: use a dynamic handheld or a condenser desk mic at reception.
  • Built-in USB, Bluetooth and FM radio: play music from a phone or flash drive with no extra player.
  • Two chimes (level 0-15) and a SIREN trigger: a tone before each announcement and an alarm from another system.
  • IR remote and power-off memory: change source and volume from across the room; settings return after an outage.

Questions you might have

‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌