BFT CFZ 2608387 Galvanized Steel Rack, 2 m Section for Sliding Gates

144.74

Product description


The BFT CFZ 2608387 is a 2 m galvanized steel rack section fixed along a sliding gate so the operator's pinion can mesh with it and drive the leaf. Order it for a new sliding gate motor install or to replace a worn rack.

====

The BFT CFZ 2608387 is the part that connects a sliding gate motor to the gate itself. The rack section is fixed horizontally along the gate leaf, the operator's pinion meshes with its teeth, and the pinion's rotation becomes the gate's side-to-side travel. Each piece is 2 m of galvanized steel, sold under code 2608387 or D571054.

BFT CFZ 2608387 specifications

  • Length: 2 m per section.
  • Material: galvanized steel.
  • Order codes: 2608387 and D571054.

How many sections does your gate need?

The rack runs the length of the moving gate leaf, not just the width of the opening. Measure the leaf, divide by 2 and round up. A 7 m leaf needs 4 sections (8 m), with the extra trimmed off the last piece. Long warehouse gates follow the same maths, so order all the pieces together and keep them identical.

Why galvanized steel

A rack sits at the bottom of the gate for its whole life, close to sand, dust and wash water. The zinc layer on galvanized steel protects it from rust, which matters in humid coastal cities such as Jeddah, Dammam and Al Khobar. Steel teeth also take pinion load on heavy gates better than nylon racks.

Installation tips

  • Start the first section at the pinion with the gate closed, then continue along the same line.
  • At each joint, hold a spare rack piece across the seam as a guide so the tooth spacing stays even.
  • Leave a small gap between rack and pinion so the gate's weight does not rest on the motor.
  • Check that the leaf is straight and its wheels run freely before fixing the rack.

Where it is used in Saudi Arabia

  • Villas in Riyadh and Jeddah converting a manual sliding garage gate to automatic.
  • Residential compounds and istirahas replacing a worn-out rack.
  • Warehouses and factories with long steel gates that need several sections.

Matching the gate operator

A toothed rack is made for sliding operators that drive the gate through a pinion. Match your motor's pinion module to the rack module before ordering. If the old rack is a different type, replace the full run rather than mixing two types on one gate.

CFZ 2608387 or the ARES BT KIT A1500?

These are two different products; neither replaces the other. The CFZ 2608387 is a 2 m mechanical steel part with no electrical components, fixed to the gate. The ARES BT KIT A1500 is a kit built on a 24V operator for gates up to 1500 kg, packed with a control unit, photocell, two remotes and a flasher, and its contents include no rack. The rack is ordered separately, once its module matches the operator's pinion.

Frequently Asked Questions

How long is one BFT CFZ 2608387 section?

2 m per piece. Divide the gate leaf length by 2 and round up to get the section count.

Can it be used outdoors?

Yes. It is galvanized steel, and the zinc coating protects the steel from rust on exposed gates.

Does the ARES BT KIT A1500 include this rack?

The kit contents include no rack, so the rack is ordered separately to cover the gate length.

Specifications

  • Model: CFZ
  • Order codes: 2608387 / D571054
  • Type: Rack for sliding gates
  • Length: 2 m per section
  • Material: Galvanized steel

Features

  • 2 m per section: work out the number of pieces straight from the gate leaf length.
  • Galvanized steel: the zinc coating protects the steel from rust on outdoor gates.
  • Purely mechanical with no wiring: no power or programming, just fixing and alignment.
  • 2 order codes, 2608387 and D571054: easy to match when you reorder extra sections.

Questions you might have

‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌
‌
‌‌
‌