Welala Coleston Natural hair dye in light brown color 5/0 - 1 package

Light Brown Colston Naturals Hair Dye contains strong colored dyeing materials and nourishing serum with natural extracts that vary depending on the color type, such as cinnamon extract for brown hair, chamomile extract for blonde hair, pomegranate extract for red hair, and I can choose from many attractive colors for Colston Naturals dye. Important instructions before dyeing hair using Colston Naturals Light Brown dye: 1- Do not use the dye on wet hair, and it is preferable not to wash the hair three days before the coloring process. 2- You should wait 5-6 months if you have used henna, because the dye cannot penetrate the layers formed by henna on the outer layer of the hair, resulting in uneven colors. 3- This dye is not used for eyebrows. 4- A sensitivity test must be performed 48 hours before coloring or dyeing the hair. 5- For the best desired results, perform a strand test. Method of using Colston Naturals Light Brown dye: 1- Preparing the coloring cream mixture: Empty the contents of the tube into a non-metallic dish (made of glass, plastic, or porcelain), then add the developer liquid and mix them together using a dye brush until you get a completely homogeneous dye mixture. Apply the dye mixture to your hair immediately after thorough mixing for the best color result. 2- Applying the coloring cream mixture: For the first time dyeing, apply the dye mixture to unwashed hair strand by strand using a dye brush. Make sure to apply the dye mixture to all hair and not leave any part out, then comb your hair with a wide-tooth comb to distribute the dye evenly over all the hair. To dye the roots, divide your hair into sections, apply the dye mixture to each section separately, and leave it on for 20 minutes. Then comb your hair evenly towards the tips. 3- Duration of leaving the product on the hair: The product should be left on the hair for 30 minutes, 20 minutes for the roots and 10 minutes for the rest of the hair. The color of the dye mixture may change during this period. 4- Finishing the dye: After the dyeing time, rinse the dye emulsion thoroughly with warm water. To fix the color, apply conditioner to your damp hair, leave it for 5 minutes, then rinse well with water. It gives you the smoothing serum with the healthy appearance you desire. How to perform the skin sensitivity test: It must be done 48 hours before coloring: Tools needed for the sensitivity test are: cotton, cotton swab, plastic container, plastic spoon. 1- Open the cap of the developer solution tube number 2, then open the cap of the coloring cream tube number 1. 2- Mix a small equal amount of coloring cream and developer solution in the plastic container. 3- Quickly close the caps of the coloring cream and developer solution. 4- Place a small amount of the prepared mixture behind your elbow on a 1 cm square area. Leave it to dry without rinsing for 48 hours. During bathing, protect the area with a tight bandage, then remove the bandage immediately afterward. 5- Check the test area after 48 hours. If there is no reaction, you are ready to proceed with coloring. 6- If a rash, burning sensation, or itching occurs, you may be allergic to one of the ingredients, and you should stop using it immediately. Strand test for Colston Naturals Light Brown dye: Perform a color test on a hair strand each time you color to determine the best timing for highlighting and achieve the best result, considering that chemical treatments such as curling, straightening, previous coloring, and sun exposure all affect the color result and timing needed. Tools needed for the strand test: scissors, tape, and a clock. Steps for the strand test for Colston Naturals Light Brown dye: 1- Cut a quarter inch of your dry hair that is dark or has a lot of white hair from near the scalp, then tape the strand with adhesive tape at the cut site. 2- Apply the remaining mixture used for the sensitivity test over the strand, covering it completely, then start timing. 3- After 15 minutes, check the strand. If the color is not as desired, return the strand to the plastic container with the mixture and monitor the color periodically until 25 minutes pass. For very light blonde color, a more saturated color, or to cover resistant white hair, you may need to leave the dyeing process up to 45 minutes. Adjust your highlighting time as follows: The appropriate time for highlighting is -------- minutes. Perform the sensitivity test 48 hours before each coloring, even if you have used coloring products before.