Sikafloor-151 - Epoxy Base - Sika 25 kg
710ر.س
Product description
What is Sika Floor 151? When it comes to durable and withstand industrial floors, everything starts from what is beneath the surface. Sika Floor 151 is an epoxy primer (Epoxy Primer) two-component, low viscosity, with a Shore D hardness of approximately 80, specifically designed to prepare and strengthen concrete surfaces before applying epoxy and polyurea flooring systems. It penetrates the pores deep into the surface, bonds the molecules, and increases adhesion strength to ≥1.5 Newtons/mm² according to EN 1542. It is used as a primer, bonding layer, and hardener for epoxy mortar — at the same time. Sikafloor-151 is a product of Swiss Sika company, legally affiliated with Sika Schweiz AG, suitable for industrial, commercial, and residential projects alike. Its volatile organic compounds (VOC) content is less than 100 g/l according to EN requirements, making it suitable for indoor application. It is classified within epoxy flooring systems as epoxy primer for concrete and epoxy bonding primer, and employed as an industrial flooring primer within the approved Sikafloor system build-up. Emaar Innovation is an authorized distributor of Sika products in Saudi Arabia — providing the original product with technical support and delivery across all regions of the Kingdom. Technical specifications of Sika Floor 151 Sika Floor 151 is an epoxy primer made of two parts (A + B) mixed at a weight ratio of approximately 2:1. Its low viscosity allows deep pore penetration, with a curing hardness of Shore D ≈ 80. Adhesion strength reaches ≥1.5 Newtons/mm² according to EN 1542, while compressive strength is ≥70 Newtons/mm² after 7 days at 20°C. Pot Life at 20°C ranges between 25 and 30 minutes, and re-coating time between 6 and 24 hours depending on temperature and humidity. The recommended thickness for the standard primer ranges between 0.3 and 0.5 mm, with coverage rates between 0.3 and 0.5 kg/m², approximately 70 to 80 m² per container depending on surface absorption. Application temperature ranges from +10°C to +30°C, and the floor can withstand service temperatures up to 60°C for short periods. The container weight is 25 kg, and its low odor makes it suitable for enclosed spaces. It can be mixed with quartz sand for leveling works or to produce epoxy mortar. Certifications obtained: EN 13813:2002, EN 1504-2:2004, EPD, EN 1542 testing, CE Marking. Uses and applications What distinguishes this product is not only its versatility but its true flexibility in the field. The engineer deals with different situations at each site, and Sika Floor 151 is designed to be the answer in more than one scenario. Main applications Primer for concrete surfaces before epoxy coatings Bonding layer for low to medium absorption surfaces Hardener for epoxy mortar Surface treatment for weak and crumbling surfaces Raising and leveling epoxy flooring layers Practical application scenario (Case Use) Let’s take a real example: an industrial warehouse of 1000 m² in Riyadh. Sikafloor-151 was applied as a primer with an average consumption of 0.4 kg/m², totaling 400 kg. After 12 hours at 25°C, a self-leveling epoxy layer was applied, achieving adhesion results exceeding 1.5 N/mm², with a noticeable reduction in the final layer consumption by about 15% — directly due to the pre-saturation of the pores. Target sectors This primer finds its place across a wide range of projects: factories and warehouses, garages and parking lots, workshops and retail stores, hospitals and government buildings, and large residential projects. Main features of Sika Floor 151 Epoxy resin Talking about features is not complete with numbers alone — the real value appears when performance, ease of application, and site convenience are combined. 1- Technical performance Adhesion strength reaching ≥1.5 N/mm² according to EN 1542 is not a theoretical number; it guarantees the long-term stability of the flooring layers. The primer penetrates the pores due to its low viscosity, supports concrete cohesion, and reduces surface dusting. The immediate result: decreased absorption of subsequent layers, thus providing an actual material saving of up to 15% in large projects. 2- Application advantages Simple mixing with a slow-speed mixer for 2-3 minutes, with a pot life of up to 30 minutes at 20°C — enough time for organized work without haste. Fully compatible with other Sikafloor systems, and its low-emission formulation (VOC < 100 g/l) makes it a practical choice for indoor application. 3- Reliability Behind each container are certified European standards: EN 13813:2002 and EN 1504-2:2004, CE Marking compliance, and an environmental declaration (EPD). Manufactured under ISO 9001 and ISO 14001 systems by Sika Schweiz AG in Switzerland. This level of accreditation makes it a trusted reference in government and industrial projects with strict requirements. Comparing Sikafloor-151 with other epoxy primers Many epoxy primers available in the market perform the basic bonding function but do not go beyond that. Sikafloor-151 differs in three key aspects: First: Adhesion strength. Sikafloor-151 achieves ≥1.5 N/mm² tested according to EN 1542, an approved European standard. Many alternative primers only claim “good adhesion” without reference numbers or independent certifications. Second: Scope of use. This primer performs multiple functions simultaneously: as a preparatory primer, bonding layer, and hardener for epoxy mortar. Single-function primers require additional materials to achieve the same result, increasing overall project costs. Third: Certifications and compatibility. Sikafloor-151 carries EN 1504-2:2004 certification for concrete protection and repair systems, a requirement for infrastructure and government projects. Most alternative primers do not have this specific certification and are not part of the integrated Sikafloor system build-up. Summary of comparison: The real difference is not in price but in performance assurance over the long term and acceptance in the technical specifications of major projects. Application method Successful application of any epoxy primer begins before opening the container. Proper preparation is half the work. 1. Surface preparation Ensure the concrete is dry with moisture ≤ 4%. Clean the surface thoroughly from oils, grease, dust, and remove any delaminated or weak layers. Concrete compressive strength should be at least 25 N/mm², and mechanical grinding is always preferred for best results. 2. Mixing Mix component A with component B at a 2:1 weight ratio. Continue mixing for 2-3 minutes at low speed until the material is fully homogeneous. If needed, quartz sand can be added according to the specified system. 3. Application Spray or roll the product, and evenly distribute at a rate of 0.3–0.5 kg/m². Allow the surface to dry for 6 to 24 hours before applying the next layer, and avoid early loading before full curing. Note: Always refer to the official technical datasheet from Sika and adapt to actual site conditions. Certifications and approvals It is not enough for the product to perform on-site — it must also be recognized by the relevant authorities. Sika Floor 151 holds EN 13813:2002 for European standards for leveling materials, EN 1504-2:2004 for concrete protection and repair systems, EN 1542 for adhesion testing, an approved environmental declaration (EPD), and CE Marking for European conformity. Fully manufactured by Sika Schweiz AG in Switzerland. These certifications are not just paper certificates; they guarantee usability in industrial and government projects with strict requirements. The product also complies with modern construction standards and may be included in projects subject to the Saudi Building Code (SBC) according to each project’s specifications. Emaar Innovation, as the authorized distributor of Sika in Saudi Arabia, provides complete technical documentation upon request. FAQs 1 - Is Sikafloor-151 suitable for indoor use? Yes, it features a VOC content below 100 g/l according to EN requirements, making it perfectly suitable for use inside residential, commercial, and industrial buildings. It does not emit harsh odors during application, reducing the need for intensive ventilation compared to high-VOC primers. This feature makes it a preferred choice in hospitals, schools, and sensitive facilities that remain operational during construction. 2 - Can it be used to treat weak concrete? Yes, it saturates the pores and bonds the surface layer due to its low viscosity, allowing deep penetration. It strengthens crumbling or hollow-structured concrete and increases its cohesion before applying subsequent epoxy layers. A key condition: concrete compressive strength must be at least 25 N/mm² to ensure approved adhesion results according to EN 1542. 3 - What is the correct time gap between applying the primer and the final layer? It ranges from 6 to 24 hours depending on temperature and relative humidity. At 20-25°C under normal conditions, 12 hours is usually sufficient. In cold or humid weather, it can extend up to 24 hours, while in hot, dry weather, 6-8 hours may suffice. The surface readiness can be checked by light touch — if the primer does not stick to the hand, it is ready for the next layer. 4 - Can Sikafloor-151 be applied on a damp surface? No, it cannot be applied on a damp surface. The concrete moisture must be ≤ 4% to ensure full adhesion according to the technical specifications. Excess moisture prevents the primer from penetrating the pores and weakens the bonding strength fundamentally. If rising moisture (Vapor Moisture) from the floor exists, it must be treated first with special products before applying any epoxy system. 5 - Is the product compatible with all Sikafloor systems? Yes, it is fully compatible with all Sikafloor epoxy and polyurea flooring systems. It is primarily designed to be the first layer within the integrated Sikafloor system build-up, ensuring chemical and mechanical compatibility among all system layers. Emaar Innovation provides the necessary technical support to select the appropriate system for each site. 6 - What is the actual difference between Sikafloor-151 and other epoxy primers in the market? Sikafloor-151 combines in one product low viscosity for deep penetration, an adhesion strength ≥1.5 N/mm² tested according to EN 1542, and can be used as a primer or component for epoxy mortar. Most importantly, it carries EN 1504-2:2004 certification for concrete repair, which many alternative primers lack. This makes it acceptable in the specifications of government and industrial projects that specifically require this standard. Order the product from the authorized distributor Emaar Innovation — the official distributor of Sika in Saudi Arabia, offering genuine products, technical support, and delivery to all regions of the Kingdom. Special offers for projects and quantities. Site inspection for only 5 SAR — deducted from the order value. Contact us now for inquiries or to request a tailored quote for your works, or browse epoxy flooring options for factories, warehouses, and parking lots.
Questions you might have

