BESANTEK BST-ET18 Clamp-On Earth Ground Resistance Tester 30A
3795ر.س
Product description
BESANTEK BST-ET18 Clamp-On Earth Resistance and Leakage Current Tester
The BESANTEK BST-ET18 measures earth-loop resistance by clamping around an earthing conductor, without disconnecting it where the installation provides a suitable return path for this method. It also measures AC leakage current up to 30 A and stores readings for comparison during electrical inspections and maintenance.
Features
- Earth-loop resistance and AC leakage-current measurement in one instrument.
- A 65 × 32 mm clamp opening for conductors that fit within it.
- Memory for up to 99 data sets and an RS232 interface for data transfer.
- Audible and visual alarms with adjustable thresholds.
- A four-digit LCD and automatic shutoff after approximately five minutes.
- Interference-signal recognition as listed by the manufacturer.
Technical specifications
| Earth-loop resistance | 0.01–1200 Ω |
| AC leakage current | 0.00 mA–30.0 A at 50 or 60 Hz |
| Finest published resistance resolution | 0.001 Ω; resolution varies with range |
| Finest published current resolution | 0.05 mA; resolution varies with range |
| Best published resistance accuracy | ±1% ±0.01 Ω; refer to the conditions for each range in the manual |
| Best published current accuracy | ±2.5% ±1 mA; refer to the conditions for each range in the manual |
| Clamp opening | 65 × 32 mm |
| Adjustable alarm thresholds | Resistance: 1–199 Ω; current: 1–499 mA |
| Memory and interface | 99 data sets; RS232 |
| Power | Four 1.5 V AA alkaline batteries |
| Operating conditions | −10 to 55 °C; 10–90% relative humidity |
| Dimensions | 285 × 90 × 66 mm |
| Instrument weight | 1160 g including batteries; not the packed shipping weight |
The resolution and best-accuracy figures above are the values published in the manufacturer summary. They do not necessarily apply across all ranges. Consult the operating manual for the selected range and measurement conditions before accepting a result.
Package contents
BST-ET18 tester, test ring, hard carrying case, RS232 data cable, software disc, batteries and instruction manual, per the manufacturer catalogue.
Applications
Inspect earth loops on installations suited to clamp testing, check AC leakage current and compare readings from inspection points during electrical maintenance.
Before purchase and use
A qualified technician must confirm that a suitable return path exists, check that the conductor fits the clamp and follow the manual and site procedures. Clamp-loop testing is not suitable for every earthing system or an isolated electrode without a return path. This measurement does not establish absence of voltage. Check that the RS232 cable and interface and the manufacturer software are compatible with the computer used for data transfer.
Frequently asked questions
Must the earthing conductor be disconnected?
It can remain connected where the installation supports clamp-loop testing and provides a suitable return path. A qualified technician determines whether the method is appropriate.
Does the 30 A figure refer to resistance measurement?
No. It is the maximum AC leakage-current range. The resistance range is 0.01–1200 Ω.
How many readings can be stored?
The memory holds up to 99 data sets. RS232 transfer requires a compatible interface and software.
Are resolution and accuracy the same across all ranges?
No. The summary gives the finest resolution and best published accuracy. Consult the manual for the selected range and its conditions.
What is the test ring used for?
It checks instrument response against the ring value following the manual. This functional check does not replace required periodic calibration.
Recommended Products
- WISEUP 100 Piece Screwdriver and Bit Set — For suitable screw fasteners during isolated maintenance; electrical insulation is not implied.
- KOELN 50 m Extension Cable — To power a computer or supporting equipment within the cable ratings; the handheld instrument itself uses its batteries.
- JADEVER 6 Piece Short Ratcheting Spanner Set — For appropriately sized nuts and bolts during maintenance after equipment isolation as required.
- JADEVER 200 A AC Clamp Meter — For separate load current and voltage measurements during electrical troubleshooting within its ratings.
- JADEVER Non Contact AC Voltage Detector — For preliminary AC voltage detection near wiring; absence of an alert does not verify that a circuit is de energized.

